Display results as :

Rechercher Advanced Search

Latest topics
» Video of BMW Disa Valve installation
by Admin Fri Jul 19, 2013 5:45 pm

» Mercedes shifter selector repair Guide and Video
by 8thvision Tue Nov 13, 2012 2:11 pm

» 98-01 Toyota Corolla Improved Winshield Washer bottle
by 8thvision Tue Nov 13, 2012 1:49 pm

» 2001 Mercedes Benz W220 Strut
by Admin Mon Nov 12, 2012 6:51 pm

» BMW Disa Valve Installation Video
by Admin Thu Nov 08, 2012 4:58 pm

» BMW M42 and M44 Engines. Disa Valve.
by 8thvision Thu Nov 08, 2012 1:17 pm

» Benz E320 Headlight Wire broken
by kimchi Wed Oct 17, 2012 6:34 pm

» Rides & Styling
by 8thvision Mon Mar 12, 2012 1:06 pm

» Marlon Oakley Graphic Design
by 8thvision Thu Mar 08, 2012 2:28 pm

» Guest Book
by Guest Mon Feb 13, 2012 1:08 pm

January 2019

Calendar Calendar

How to install: Camry Outside/Inside Door Handle (Installation Guide)

Go down

How to install: Camry Outside/Inside Door Handle (Installation Guide)

Post  Admin on Thu Dec 29, 2011 1:45 pm

This guide is for 97-01 Toyota Camry Inside and outside Door handles, please note. This guide will provide enough info for all trim but is not specifically suited for one variation of the steps may be required.

Video (Inside Door Handle Only)

Raise the window all the way up. If your Camry has power windows or locks, open the hood and disconnect the negative battery cable after raising the window.

Remove the bezel surrounding the inner door handle by prying it away with a trim stick. On some models, you must pry away the decorative cover in the middle of the bezel and remove the screw underneath the cover.

Pry off the switch plate for the power windows and the trim plate near the door's rear view mirror using the trim stick. Disconnect the electrical connectors for the switch plate, and take note that one of the panel's mounting screws is behind the plate.

Detach the door trim panel by unscrewing all of its mounting screws, prying around the panel's edge with the trim stick to release its clips and pulling the trim panel up from the door. Unplug any electrical connectors from behind the panel.

Remove the speaker from the door by removing its mounting screws, pulling it out and disconnecting its electrical connector.

Peel back the plastic water shield on the door.

Removing the Inside Handles

Remove the two screws on both sides of the handle.

Push the handle forward and pull out to disconnect from door.

Lift the metal locking and handle rods to remove handle completely.

Removing the Outside Handles
Detach the actuating rod that connects the outside door lock to the latch by disengaging its clips. These clips are accessed through the access hole in the door.

Pull out the circular, rubber access plug in the edge of the door to reveal the lock cylinder bolt. Loosen this bolt with a Torx socket; the bolt will not come off completely.

Slide the outer door handle toward the rear of the car to remove the handle.

Disengage the inner door handle from the lock cylinder from by removing the bolt from inside the door opening and squeezing the clips along the outer edge. Remove the handle from the door.

Replacing the Handles

Reconnect the rods and Place inside handle flat against the door with the locking hooks on back inside the securing slot. Then push handle back to secure it and line up holes, one complete replace the screws.

Install the new outer door handle onto the door by sliding it frontward into position. Secure it by tightening the bolt on the door's edge.

Reconnect the actuating rod to the door latch and lock cylinder by using its clips.

Reinstall the entire door trim panel in reverse order of installation.

Last edited by 8thvision on Thu Feb 16, 2012 4:50 pm; edited 7 times in total (Reason for editing : Incomplete)

Posts : 24
Join date : 2011-07-14

Back to top Go down

Back to top

- Similar topics

Permissions in this forum:
You cannot reply to topics in this forum